[ Pobierz całość w formacie PDF ]
ATLAS MATERIALS SNAPPING TURTLE SUBMERSIBLE
Instructions
1.
Upper hull
. Score along black lines. Assemble top half
first, gluing sides to fore and aft portions. Allow to dry.
Fold up tabs on bottom portion. Fold over top half and
glue to bottom (like closing a clamshell). Make sure
bottom portion does not warp by maintaining pressure
until glue is dry.
2.
Lower hull
. Score along black lines. Fold over all tabs.
It is easiest to begin gluing at the forward section.
Wrap the bottom around the windows, allowing it to
dry before continuing. The bottom hull has a
rectangular cross-section, and is essentially a glorified
box.
3.
Upper hatch
. Score tabs and fold lines. The long spiral
piece wraps around the outside edge, forming a six-sid
ed cone. It is easiest to glue the tabs to the upper part
of the hatch, then fold the bottom of the hatch in. Al
low to dry.
4.
Fins
(optional)
.
Select either a large or small fin for
the aft section. Carefully score the tabs on the reverse
side. The tab for the aft of the submarine may be
omitted, as the fin is intended to represent a rudder.
The fin may not be as strong, however.
5.
Light mount
. Score tabs. Fold and glue into a box
shape with two slanting sides.
6.
Lights.
Score, fold and glue lights into a box shape
with one sloping side.
7.
MHD drives.
The port and starboard MHD drives are
mirror images of one another. Assemble by folding the
sides together to form a tube, then fold the front and
aft sections to complete the shape.
8.
Thruster mount.
This piece folds into a wedge shaped
box. As with the
MHD drives
, it is easiest to form a
tube, then fit the smaller end pieces in to form the
correct shape.
9.
Thruster units.
There are 3 separate thruster units.
Score and fold each of the tabs. Begin by folding up
one end and slowly gluing the tabs to form a cylinder.
Glue on long edge, then fold over remaining end to
complete. Set aside to dry.
10.
Base.
The base is assembled in the same manner as
the upper hatch.
11.
Shaft.
The shaft folds together to form a box with
one sloping side. As with the MHD drives, fold together
to form a tube, then fold the end pieces over to
complete the shape.
12. Glue the lower hull to the upper hull, making sure
that the forward sections are aligned and that the
lower hull is correctly centred.
13. Glue port and starboard MHD drives to both the lower
and upper hulls, using the hull marks as a reference.
14. Glue thruster mount to aft section of upper hull. The
mount does not need to be flush -- the mount acts as a
backup dive plane.
15. Glue the three assembled thrusters to the thruster
mount. The silver/grey section points aft, but that's
purely an aesthetic choice. The thrusters may be
pointed in any direction desired, as they control the XY
coordinates of the submersible.
16. Cement the lights to the light bar using the sloped
edge of the light. Each light may be rotated to any
desired angle.
17. Glue the completed light bar to the forward section
of the lower hull.
18. Attach the fin to the aft section of the upper hull,
making sure it is centred.
19. Glue the shaft to the centre of the base. Use lots of
glue and set aside until completely dry, or the model
will fall off the base.
20. Glue the completed model to the base, using lots of
glue. The sloped top of the shaft allows the model to
be rotated to display the top or bottom, as desired.
Assembly Tips
If you have printed this file directly onto cardstock, spray
the paper with Testor's Dullcote or an artist's fixative, as
most inkjet glue is water soluble.
If you plan to make multiple submarines, print out one copy
and colour photcopy it. Glue the colour copies to cardstock
with 3M Photomount spray glue.
Score along the fold lines before cutting out the model. It
will save time and be more accurate.
Test fit all the parts before gluing. Even though this model
has been thorougly tested, various paper types may cause
slight discrepancies.
If you don't want the model to be permanently attached to
the base, use a fabric snap on the top of the shaft. Glue the
other half of the shaft to the bottom of the sub. This will
allow you to rotate the model on the base and remove it
completely if desired. Make sure the glue is completely dry
on both halves before snapping and unsnapping the model.
© 2001 Paul Lesack. Permission granted to copy for personal use only
Blue Planet ©1997 Biohazard Games
1 of 3
ref: BPV2 PG 005.159
 Upper hull
Glue lower
hull here
Starboard
MHD
drive
Port
MHD
drive
Base
Glue thruster mount here
Shaft
score on reverse side
this piece optional
Rear Fin 1
Glue
hatch
here
cut here
Rear Fin 2
Top hatch
 Thruster unit
Thruster unit
Light mount
Glue to upper hull
Thruster mount
Lights
Glue to
upper hull
Port
MHD
drive
Starboard
MHD
drive
Bottom hull
Thruster unit
  [ Pobierz całość w formacie PDF ]